Example: air traffic controller
MT. 8830018 - REV C 06/13 PRINTED IN USA PAGE 1 OF 2 RHA RATE OF RISE/FIED TEMPERA TURE HEAT DETECTOR Potter Electric Signal Company, LLC • …
Text of RHA
MKT. #8830018 - REV C06/13PRINTED IN USAPAGE 1 OF 2RHARATE OF RISE/FIXED TEMPERATURE HEAT DETECTOR Potter Electric Signal Company, LLC St. Louis, MO Cust Service: 866-240-1870 Tech Support: 866-956-1211 Canada: 888-882-1833 combination Rate of Rise/Fixed Temperature Heat Sensor (RHA) is a listed Analog/Addressable combination temperature heat sensor compatible with any fire alarm control panel that has the Potter/Nohmi protocol. The heat sensing portion utilizes a proven thermistor for accurate and reliable heat detection. The sensor and base (not included) are made of a durable plastic in an eggshell white (off white) to blend in with the ceiling. The RHA is UL and cUL listed with a selectable fixed temperature point from 135 to 174 and a rate of rise feature. The rate-of-rise operates when the temperature increases 12-15 F occurs. The heat sensor is ideal for installations needing the earlier heat detection. The RHA has two LEDs that allow for 360 viewing. The sensor is compatible with any of the Potter/Nohmi bases and simply twists on. The RHA is addressed using the hand held programmer or the control panel addressing function. SpacingThe RHA spacing is dependent on the alarm set-point. The unit is listed from 135 F to 174 F. However as the temperature setting increases, the spacing set-pointRHA Spacing135 to 170 F (57 to 76 C) Max. 50 ft171 to 174 F (77 to 79 C)Max. 15 ftThe system has a maximum of 13 LEDs that can be turned on simulta-neously. If the system already has 13 LEDs on, the RHA will operate even though the LED will not the AddressEach addressable module, smoke sensor, heat detector and combination sensor/detector must have the address set before connecting the device to the SLC loop. The address is set using the hand held device programmer or the addressing feature on the control Features Adjustable fixed 135 to 174 Fahrenheit Rate of rise feature with 10-12 F per minute detection LEDs for 360 viewing Low profile Reliable detection technologyItemFHAWorking voltage to VStandby current325 AAlarm indicator2 LEDsAlarm indicator mA set-point range135 to 174 F/ 57 to 79 CRate-of-rise12 to 15 FInstallation temperature range32 to 100 F / 0 to 38 COperating relative humidity range0% to 93% (Non-condensing)Start-up timeMax. 1 number of addresses per loop127Maximum number of lighted indicators in alarm per WhiteWeight (without base)73g ( )Dimensions (without base)Height: in (38mm)Diameter: inches (99mm)Approvals / ListingsUL, ULC, CSFM, connecting a device to the SLC loop, take the following precautions to prevent potential damage to SLC or device. Verify the following:1. Power to the device is removed2. Field wiring is correctly Field wiring has no open or short discrepancies and notify appropriate includes a 5 year warrantyS247767270-0328:0193MKT. #8830018 - REV C06/13PRINTED IN USAPAGE 2 OF 2RHARATE OF RISE/FIXED TEMPERATURE HEAT DETECTOROperationThe RHA is an analog/addressable sensor that uses one address on the Signaling Line Circuit (SLC) of a compatible fire alarm control panel. The unit communicates with the control panel as it is polled. The LEDs flash every time the unit is polled and they will latch steady if the unit is in an active status. The RHA is a single sensor that may be used in a wide variety of applications for property protection. The RHA has a the rate of rise heat detection to provide detection of an escalating fire. The unit has a sleek design and low profile for pleasing aesthetics. The temperature sensor is protected within the mold of the unit to prevent accidental damage. Compatible BasesAll bases will mount on a single gang, double gang, octagon, 4 square or mud ring electrical Standard BaseAB-66 Standard BaseAIB6 base with an isolator module included. The base is pre-wired with a pluggable jumper to the base with a dual relay module included. One relay is rated for 8 amps at 240 VAC/30 VDC and the second is rated for 2 amps at 240 VAC/30 VDC. The base is pre-wired with a pluggable jumper to the " base with sounder module included. Sound pattern is provided from external source. The base is pre-wired with a pluggable jumper into the module.