Example: marketing

NEWAGE MX321 AVR, REPLACEMENT - VOLTAGE …

Compatible with Newage MX321, Stamford MX321, E000-23212, Onan 305-0823 . Same fit form and function as the Original Newage MX321. Generator Automatic Voltage

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Text of NEWAGE MX321 AVR, REPLACEMENT - VOLTAGE …

Compatible with Newage MX321, Stamford MX321, E000-23212, Onan 305-0823 Same fit form and function as the Original Newage MX321 Generator Automatic Voltage Regulator Operation Manual Self Excited Automatic Voltage Regulator * Use for reference purpose only and not a genuine Newage product. HNEWAGE MX321 AVR, REPLACEMENTTo place an order click here --------- >For our hompage click here ---------- >For more information click here ----- > MX321 is a two phase sensed Automatic Voltage ________________________________________ ________________________________________ ______ 2 1. INTRODUCTION Sensing Input Voltage 190 ~ 264 VAC Max, 2 or 3 phase Frequency 50 / 60 Hz, nominal Power Input (PMG) Voltage 170 ~ 220 VAC Max, 3 phase 3 wire Current 3A phase Frequency 100 ~ 120 Hz, nominal Output Voltage Max. 120 VDC Current Continuous Intermittent 6A for 10 sec Resistance Min. 15 ohm Voltage Regulation < ( with 4% engine governing ) Voltage Build-up Residual voltage at AVR terminal > 5 VAC Thermal Drift per C change in AVR ambient External Volts Adjustment 10% with 5K ohm 1 watt trimmer Unit Power Dissipation Max. 18 watt Under Frequency Protection (Factory Setting) Set point 95% Hz Slope 100 ~ 300% down to 30 Hz Current Limit Input 10 ohms burden Sensitivity range ~ 1A Soft Start Ramp Time ~ 4 sec. Analogue Input Max. Input 5 VDC Sensitivity 1V for 5% generator volts Input Resistance 1K ohm Droop Input Burden 10 ohm Max. sensitivity A for 5% droop (PF=0) Max. input A Over Voltage Detector Input Set point 300V. Time delay 1 sec (fixed) CB trip coil volts 10 ~ 30 VDC CB trip coil resistance 20 ~ 60 ohms Over Excitation Protection Set point 75 VDC Time delay 8 ~ 15 sec (fixed) Typical System Response AVR response 10 ms Filed current to 90% 80 ms Machine Volts to 97% 300 ms Environmental 100Hz ~ 2kHz Operating temperature -40 to +70 C Relative Humidity 0 ~ 70 C 95% (see note 7) Storage temperature -55 to +80 C Dimensions 203mm L * 153mm W * H Weight 530g 2% 2. GENERAL DESCRIPTION Regulator and forms part of the excitation system for a brush-less generator. Excitation power is derived from a three-phase permanent magnet generator (PMG), to isolate the AVR control circuits from the effects of nonlinear loads and to reduce radio frequency interference on the generator terminals. Sustained generator short circuit current is another feature of the PMG system. The AVR senses the voltage in the main generator winding and controls the power fed to the exciter stator and hence the main rotor to maintain the generator output voltage within the specified limits, compensating for load, speed, temperature and power factor of the generator. Soft start circuitry is included to provide a smooth controlled build up of generator output MX321 AVR ________________________________________ ________________________________________ ______ 3 A frequency measuring circuit continually monitors the shaft speed of the generator and provides under-speed protection of the excitation system by reducing the generator output voltage proportionally with speed below a pre-settable threshold. A further enhancement of this feature is an adjustable volts per Hertz slope to improve engine recovery time on turbo charged engines. Soft start circuitry is included to provide a smooth controlled build up of generator output voltage. Uncontrolled excitation is limited to a safe period by internal shutdown of the AVR output device. This condition remains latched until the generator has stopped. Provision is made for the connection of a remote voltage trimmer, allowing the user fine control of the generator s output. An analogue input is provided allowing connection to a controller or other external devices with compatible output. The AVR has the facility for droop CT connection, to allow parallel running with other similarly equipped generators. NOTE : 1. Derate linearly from at 50 C to at 70 C. 2. The stated voltage regulation may not be maintained in the presence of certain transmitted radio signals. Any change in regulation will fall within the limits in Criteria B of : 2001. 3. After 10 minutes. 4. Applies to Mod status E onwards. Generator de-rate may apply. Check with factory. Factory set, semi-sealed, jumper selectable. 5. Any device connected to the analogue input must be fully looting (galvanically isolated from ground), with an insulation strength of 500V ac. 6. Non condensing. 3. SUMMARY OF AVR CONTROLS CONTROL FUNCTION DIRECTION VOLTS To adjust generator output voltage Clockwise increases output voltage STABILITY To prevent voltage hunting Clockwise increase the damping effect UFRO To set the UFRO knee point Clockwise reduces the knee point frequencyDROOP To set the generator droop to 5% at 0pf Clockwise increases the droop TRIM To optimize analogue input sensitivity Clockwise increases the gain or sensitivity EXC To set the over excitation cut off level Clockwise increase the cut off level DIP To set the frequency related voltage dip Clockwise increases the voltage dip DWELL To set the HZ related recovery time Clockwise increases the recovery time I LIMIT To set the stator current limit Clockwise increases the current limit OVER V To set the over voltage trip level Clockwise increases the trip level RAMP To set the no load voltage RAMP up time Clockwise increases the voltage ramp time RMS To set 3 phase RMS detected 4. ADJUSTMENT OF AVR CONTROLS Voltage Adjustment The generator output voltage is set at the factory, but can be altered by careful adjustment of the VOLTS control on the AVR board, or by the external hand trimmer if fitted. Terminals 1 and 2 on the AVR will be fitted with a shorting link if no hand trimmer is required. WARNING Do not increase the voltage above the rated generator voltage. If in doubt, refer to the rating plate mounted on the generator case. Do not ground any of the hand trimmer terminals, as these could be above earth potential. Failure to observe this could cause equipment damage. If a replacement AVR has been fitted or re-setting of the VOLTS adjustment is required, proceed as follows :NEWAGE MX321 AVR ________________________________________ ________________________________________ ______ 4 1. Before running generator, turn the VOLTS control fully anti-clockwise. 2. Turn remote volts trimmer (if fitted) to midway position. 3. Turn STABILITY control to midway position. 4. Connect a suitable voltmeter (0~300V ac) across line to neutral of the generator. 5. Start generator set, and run on no load at nominal frequency 50~53Hz or 60~63Hz. 6. If the red Light Emitting Diode (LED) is illuminated, refer to the Under Frequency Roll Off (UFRO) 7. Carefully turn VOLTS control clockwise until rated voltage is reached. 8. If instability is present at rated voltage, refer to stability adjustment, then re-adjust voltage if necessary. 9. Voltage adjustment is now completed. Stability Adjustment The AVR includes stability or damping circuit to provide good steady state and transient performance of the generator. A jumper link selector is provided to optimize the response of the stability circuit to various size generators. The link should be positioned as shown in the diagram according to the KW rating of the generator. The correct setting of the Stability adjustment can be found by running the generator at no load and slowly turning the stability control anti-clockwise until the generator voltage starts to become unstable. The optimum or critically damped position is slightly clockwise from this point ( where the machine volts are stable but close to the unstable region). Under Frequency Roll Off (UFRO) Adjustment The AVR incorporates an under-speed protection circuit which gives a volts/Hz characteristic when the generator speed falls below a presentable threshold known as the knee point. The red Light Emitting Diode (LED) gives indication that the UFRO circuit is operating. The UFRO adjustment is preset and sealed and only requires the selection of 50 or 60Hz and 4 pole or 6 pole, using the jumper link as shown in the diagram. For optimum setting, the LED should illuminate as the frequency falls just below nominal, 47Hz on a 50Hz system or 57Hz on a 60Hz system. DROOP Adjustment Generators intended for parallel operation are fitted with a quadrature droop which provides a power factor dependent signal for the AVR. The is connected to S1, S2 on the AVR, (see generator wiring diagram for details). The DROOP adjustment is normally preset in the works to give 5% voltage droop at full load zero power factors. Clockwise increases the amount of signal injected into the AVR and increases the droop with lagging power factor (cos ). With the control fully anti-clockwise there is no droop. Trim Adjustment An analogue input (A1 A2) is provided to connect to the controller or other devices. It is designed to accept dc signals up to 5 volts. The dc signal applied to this input adds to the AVR sensing circuit. A1 is connected to the AVR 0 volts. Positive on A2 increases excitation. Negative on A2 decreases excitation. The TRIM control allows the user to adjust the sensitivity of the input. With TRIM fully anti-clockwise the externally applied signal has no effect. Clockwise it has maximum effect. Normal setting is fully clockwise when used with a controller. WARNING Any devices connected to this input must be fully floating and galvanically isolated from ground, with an insulation capability of 500V ac. Failure to observe this could result in equipment damage. Er Excitation (EXC) Adjustment This adjustment is set and sealed in the works and should not be tampered with. An over excitation condition is indicated by the illumination of the red LED which also indicates under-speed running and over-volts. The generator must be stopped to reset an over-excitation trip. NEWAGE MX321 AVRMX321 DIP Adjustment Current Limit (I LIMIT) Adjustment This feature is mostly used when the generator is coupled to turbo charged engines with limited block load acceptance. The feature works by increasing the V/Hz slope to give greater voltage roll off in proportion to speed. This feature is mostly used to limit short circuit current or to provide a current limit on motor starting. To use this feature, current limit CT s of the correct ratio need to be connected to the AVR S1 S2 terminals. There is an internal time limit of 10 seconds. Consult the factory before using this feature. With the DIP control fully anti-clockwise, the generator voltage will follow the normal V/Hz line as the speed falls below nominal. Turning the DIP control clockwise provides greater voltage roll off aiding engine recovery. OVER VOLTAGE (OVER V) ADJUSTMENT This adjustment is set and sealed in the works and should not be tampered with. An over voltage condition is indicated by the illumination of the red LED which also indicates under-speed running and over-excitation. The generator must be stopped to reset an over-voltage trip. DWELL This feature is mostly used when the generator is coupled to turbo charged engines with limited block load acceptance. The feature works by introducing a delay between speed recovery and voltage recovery and allows a greater DIP setting without instability. RAMP The AVR includes a soft start or voltage ramp-up circuit to control the rate of voltage build up, when the generator runs up to speed. This is normally pre-set and sealed to give a voltage ramp-up time of approximately 3 seconds. If required, this can be adjusted between the limits defined in the specification. With the DWELL control fully anti-clockwise, the generator voltage will follow the V/Hz line. Turning the DWELL control clockwise increase the delay time between speed recovery and voltage recovery. 5. FITTING AND OPERATING ( Refer to generator wiring diagram for connection details ) Outline Drawing Figure 1 ________________________________________ ________________________________________ ______ 5 NEWAGE MX321 AVR RampK2 K1 P2 P3P4 XX X 67 812VoltsI E1B0 B1CBAOver VS1S2S1S2S1S2A1A23216P60HZ4P50HZ4P60HZNo link 6P50HZ<90KW90-550KW>550KW ________________________________________ ________________________________________ ______ 6 If the step above can t make the charger working still please contact with us. ~GFigure 2 Jisposition Drawing P4P3P2PMGXXX S2121K 678K1 K2B0 B1E0 E1 UVW123ABC Figure 3 Wiring DrawingNote : When the system voltage over 220VAC, a transformer is necessary at sensing input terminal is recommend. Exciter Generator3 Bridge1K: For external adjustedNEWAGE MX321 AVRMX321MX321

Related search results