Example: air traffic controller

Material Safety Data Wahl Clipper Oil Sheet

Material Safety Data Sheet Wahl Clipper Oil SECTION 1 PRODUCT AND COMPANY IDENTIFICATION Chevron Superlafi White Oil Product Use: White oil Product Number(s ...

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Text of Material Safety Data Wahl Clipper Oil Sheet

Material Safety Data Sheet Wahl Clipper Oil SECTION 1 PRODUCT AND COMPANY IDENTIFICATION Chevron Superla White Oil Product Use: White oil Product Number(s): CPS231004, CPS231005, CPS231006, CPS231007, CPS231008, CPS231009, CPS231010, CPS231011, CPS231013, CPS231062, CPS231067, CPS231075, CPS231081 Synonyms: Chevron Superla White Oil 10, Chevron Superla White Oil 13, Chevron Superla White Oil 18, Chevron Superla White Oil 21, Chevron Superla White Oil 22, Chevron Superla White Oil 31, Chevron Superla White Oil 35, Chevron Superla White Oil 38, Chevron Superla White Oil 5, Chevron Superla White Oil 50, Chevron Superla White Oil 7, Chevron Superla White Oil 8, Chevron Superla White Oil 9 Company Identification ChevronTexaco Global Lubricants 6001 Bollinger Canyon Rd. San Ramon, CA 94583 United States of America Transportation Emergency Response CHEMTREC: (800) 424-9300 or (703) 527-3887 Health Emergency ChevronTexaco Emergency Information Center: Located in the USA. International collect calls accepted. (800) 231-0623 or (510) 231-0623 Product Information email : Product Information: (800) LUBE TEK MSDS Requests: (800) 414-6737 SECTION 2 COMPOSITION/ INFORMATION ON INGREDIENTS COMPONENTS CAS NUMBER AMOUNT White mineral oil 100 %weight This material complies with Food And Drug Administration Regulation code of Federal Regulations, Title 21. SECTION 3 HAZARDS IDENTIFICATION IMMEDIATE HEALTH EFFECTS Eye: Not expected to cause prolonged or significant eye irritation. Skin: Contact with the skin is not expected to cause prolonged or significant irritation. Contact with the skin is not expected to cause an allergic skin response. Not expected to be harmful to internal organs if absorbed through the skin. Ingestion: Not expected to be harmful if swallowed. Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include coughing and difficulty breathing. SECTION 4 FIRST AID MEASURES Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water. Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse. Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice. Inhalation: No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs. SECTION 5 FIRE FIGHTING MEASURES FIRE CLASSIFICATION: OSHA Classification (29 CFR ): Not classified by OSHA as flammable or combustible. NFPA RATINGS: Health: 0 Flammability: 1 Reactivity: 0 FLAMMABLE PROPERTIES: Flashpoint: (Cleveland Open Cup) 129 C (265 F) (Min) Autoignition: No Data Available Flammability (Explosive) Limits (% by volume in air): Lower: Not Applicable Upper: Not Applicable EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames. PROTECTION OF FIRE FIGHTERS: Fire Fighting Instructions: This material will burn although it is not easily ignited. For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing apparatus. Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion. SECTION 6 ACCIDENTAL RELEASE MEASURES Protective Measures: Eliminate all sources of ignition in vicinity of spilled material. Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying non-combustible absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable containers and dispose of in a manner consistent with applicable regulations. Reporting: Report spills to local authorities and/or the Coast Guard's National Response Center at (800) 424-8802 as appropriate or required. SECTION 7 HANDLING AND STORAGE General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of water. Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate mitigating procedures. For more information, refer to OSHA Standard 29 CFR , 'Flammable and Combustible Liquids', National Fire Protection Association (NFPA 77, 'Recommended Practice on Static Electricity', and/or the American Petroleum Institute (API) Recommended Practice 2003, 'Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents'. Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid, and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and cause injury or death. Empty containers should be completely drained, properly closed, and promptly returned to a drum reconditioner or disposed of properly. SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION GENERAL CONSIDERATIONS: Consider the potential hazards of this material (see Section 3), applicable exposure limits, job activities, and other substances in the work place when designing engineering controls and selecting personal protective equipment. If engineering controls or work practices are not adequate to prevent exposure to harmful levels of this material, the personal protective equipment listed below is recommended. The user should read and understand all instructions and limitations supplied with the equipment since protection is usually provided for a limited time or under certain circumstances. ENGINEERING CONTROLS: Use in a well-ventilated area. PERSONAL PROTECTIVE EQUIPMENT Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear safety glasses with side shields as a good safety practice. Skin Protection: No special protective clothing is normally required. Where splashing is possible, select protective clothing depending on operations conducted, physical requirements and other substances in the workplace. Suggested materials for protective gloves include: Nitrile Rubber, Silver Shield, Viton. Respiratory Protection: No respiratory protection is normally required. If user operations generate an oil mist, determine if airborne concentrations are below the occupational exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection from the measured concentrations of this material. For air-purifying respirators use a particulate cartridge. Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not provide adequate protection. Occupational Exposure Limits: Component Agency TWA STEL Ceiling Notation White mineral oil ACGIH 5 mg/m3 10 mg/m3-- -- White mineral oil OSHA Z-1 5 mg/m3 -- -- -- SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Attention: the data below are typical values and do not constitute a specification. Color: Colorless Physical State: Liquid Odor: Petroleum odor pH: Not Applicable Vapor Pressure: < mmHg @ C (100 F) Vapor Density (Air = 1): >1 Boiling Point: >260 C (500 F) Solubility: Soluble in hydrocarbons; insoluble in water Freezing Point: Not Applicable Melting Point: Not Applicable Specific Gravity: - @ C ( F) / C ( F) Viscosity: cSt - 90 cSt @ 40 C (104 F) (Min) SECTION 10 STABILITY AND REACTIVITY Chemical Stability: This material is considered stable under normal ambient and anticipated storage and handling conditions of temperature and pressure. Incompatibility With Other Materials: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc. Hazardous Decomposition Products: None known (None expected) Hazardous Polymerization: Hazardous polymerization will not occur. SECTION 11 TOXICOLOGICAL INFORMATION IMMEDIATE HEALTH EFFECTS Eye Irritation: The eye irritation hazard is based on evaluation of data for similar materials or product components. Skin Irritation: The skin irritation hazard is based on evaluation of data for similar materials or product components. Skin Sensitization: The skin sensitization hazard is based on evaluation of data for similar materials or product components. Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for similar materials or product components. Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for similar materials or product components. Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for similar materials or product components. SECTION 12 ECOLOGICAL INFORMATION ECOTOXICITY The toxicity of this material to aquatic organisms has not been evaluated. Consequently, this material should be kept out of sewage and drainage systems and all bodies of water. ENVIRONMENTAL FATE This material is considered inherently biodegradable. This material is not expected to present any environmental problems other than those associated with oil spills. This material is not expected to be readily biodegradable. See Section 6 for Accidental Release Measures. SECTION 13 DISPOSAL CONSIDERATIONS Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. Contact your sales representative or local environmental or health authorities for approved disposal or recycling methods. SECTION 14 TRANSPORT INFORMATION The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods Regulations, for additional description requirements ( , technical name) and mode-specific or quantity-specific shipping requirements. DOT Shipping Description: PETROLEUM OIL, , NOT REGULATED AS A HAZARDOUS MATERIAL IMO/IMDG Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORTATION UNDER THE IMDG CODE ICAO/IATA Shipping Description: NOT REGULATED AS DANGEROUS GOODS FOR TRANSPORTATION UNDER ICAO SECTION 15 REGULATORY INFORMATION EPCRA 311/312 CATEGORIES: 1. Immediate (Acute) Health Effects: NO 2. Delayed (Chronic) Health Effects: NO 3. Fire Hazard: NO 4. Sudden Release of Pressure Hazard: NO 5. Reactivity Hazard: NO REGULATORY LISTS SEARCHED: 01-1=IARC Group 1 03=EPCRA 313 01-2A=IARC Group 2A 04=CA Proposition 65 01-2B=IARC Group 2B 05=MA RTK 02=NTP Carcinogen 06=NJ RTK 07=PA RTK No components of this material were found on the regulatory lists above. CHEMICAL INVENTORIES: All components comply with the following chemical inventory requirements: AICS (Australia), DSL (Canada), EINECS (European Union), KECI (Korea), PICCS (Philippines), TSCA (United States). NEW JERSEY RTK CLASSIFICATION: Under the New Jersey Right-to-Know Act L. 1983 Chapter 315 34:5A-1 et. seq., the product is to be identified as follows: PETROLEUM OIL WHMIS CLASSIFICATION: This product is not considered a controlled product according to the criteria of the Canadian Controlled Products Regulations. SECTION 16 OTHER INFORMATION NFPA RATINGS: Health: 0 Flammability: 1 Reactivity: 0 HMIS RATINGS: Health: 0 Flammability: 1 Reactivity: 0 (0-Least, 1-Slight, 2-Moderate, 3-High, 4-Extreme, PPE:- Personal Protection Equipment Index recommendation, *- Chronic Effect Indicator). These values are obtained using the guidelines or published evaluations prepared by the National Fire Protection Association (NFPA) or the National Paint and Coating Association (for HMIS ratings). LABEL RECOMMENDATION: Label Category : BASE OIL 1 REVISION STATEMENT: This revision updates the following sections of this Material Safety Data Sheet: 1,2,3,9,14,15 Revision Date: 07/08/2004 ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT: TLV - Threshold Limit Value TWA - Time Weighted Average STEL - Short-term Exposure Limit PEL - Permissible Exposure Limit CAS - Chemical Abstract Service Number ACGIH - American Conference of IMO/IMDG - International Maritime Government Industrial Hygienists Dangerous Goods Code API - American Petroleum Institute MSDS - Material Safety Data Sheet CVX - ChevronTexaco NFPA - National Fire Protection Association (USA) DOT - Department of Transportation (USA) NTP - National Toxicology Program (USA)IARC - International Agency for Research on Cancer OSHA - Occupational Safety and Health Administration Prepared according to the OSHA Hazard Communication Standard (29 CFR ) and the ANSI MSDS Standard ( ) by the ChevronTexaco Energy Research & Technology Company, 100 Chevron Way, Richmond, California 94802. The above information is based on the data of which we are aware and is believed to be correct as of the date hereof. Since this information may be applied under conditions beyond our control and with which we may be unfamiliar and since data made available subsequent to the date hereof may suggest modifications of the information, we do not assume any responsibility for the results of its use. This information is furnished upon condition that the person receiving it shall make his own determination of the suitability of the material for his particular purpose.

Related search results